23.31Wh Calculated Energy for Longer Service Intervals
This 3.7 V lithium polymer battery provides a substantial energy budget for longer standby periods, frequent communication, active operating cycles and reduced service frequency planning.
3.7 V High-Temperature Lithium Polymer Battery
3.7 V 6300mAh Lithium Polymer Battery 115377
The 115377 lipo battery combines 3.7 V nominal voltage, 6300mAh capacity, an 11 mm × 53 mm × 77 mm pouch envelope, a 1C charging rate and 40mΩ internal resistance. Its long rectangular format provides approximately 23.31Wh of calculated energy for electronic products that need extended energy storage within a defined battery pocket.
11537753 × 77 mm11 mm profile
6300mAh LiPo115377 reference format
115377 High-Temperature LiPo BatteryNeutral reference visual for long-format equipment with extended runtime planning
3.7 V · 23.31 WhProduct snapshot
A 6300mAh LiPo Format for Extended Energy Planning
The 115377 LiPo battery combines 6300mAh capacity with an 11 mm × 53 mm × 77 mm pouch envelope. Its long rectangular footprint helps product teams plan a larger energy reserve when the enclosure provides a defined linear battery pocket. See the high-temperature lithium polymer battery range when comparing nearby formats.
Long-format Geometry for Battery-Pocket Planning
The listed 53 mm × 77 mm footprint and 11 mm thickness give engineering teams a clear starting point for cable routing, retention, enclosure depth and thermal clearance reviews.
3.7 VNominal voltage
≈23.31WhCalculated energy
11 mmBattery thickness
77 mmBattery length
Technical data
115377 Battery Specifications
The 115377 lipo battery combines a 3.7 V nominal voltage, 6300mAh capacity, 1C charge rate and 11 mm × 53 mm × 77 mm dimensions for extended-runtime electronics and high-temperature battery evaluation.
| 115377 Mechanical and Electrical Specifications | |
|---|---|
| Product number | 115377 |
| Nominal voltage | 3.7 V |
| Rated capacity | 6300mAh |
| Charge rate | 1C |
| Battery dimensions | 11 mm × 53 mm × 77 mm |
| Internal resistance | 40mΩ |
| Calculated Electrical References | |
| Standard charge current | Approx. 3150mA |
| Rapid charge current | Approx. 6300mA |
| Standard discharge current | Approx. 1260mA |
| Maximum discharge current | Approx. 6300mA |
| Calculated energy | Approx. 23.31Wh |
The 115377 lithium polymer battery is listed at 3.7 V, 6300mAh, 1C charging, 11 mm × 53 mm × 77 mm and 40mΩ internal resistance. Confirm charging, discharge, protection, connector and high-temperature performance for the intended device and operating conditions before production.
Product characteristics & advantages
Why Evaluate the 115377 6300mAh High-Temperature LiPo Battery?
The 115377 model brings together a 23.31Wh calculated energy budget, 11 mm profile, 53 mm × 77 mm footprint, 6300mAh capacity and 40mΩ internal resistance. Its main design value is extended energy storage in a long rectangular format.
The 115377 lithium polymer battery is intended for OEM teams that need a substantial energy reserve and can allocate a defined long battery pocket in the finished device. Its approximately 23.31Wh calculated energy supports early comparisons of extended service intervals, frequent wireless communication and active operating cycles. The 53 mm × 77 mm footprint provides a linear packaging reference, while the 11 mm thickness defines the enclosure depth and clearance conversation. The listed 1C charge rate and 40mΩ internal resistance provide starting points for charger matching and voltage-drop discussions. Because temperature affects resistance, voltage stability, available capacity and charging behavior, contact ZERNE to confirm the final high-temperature configuration.
6300mAh for Extended Operating Plans
The 6300mAh capacity and approximately 23.31Wh calculated energy help compare longer reporting intervals, reduced service frequency and active operating demands in higher-energy OEM devices.
53 mm × 77 mm Area for Linear Battery Pockets
The 53 mm × 77 mm footprint provides a long rectangular reference for products with a dedicated battery channel. Review cable exit, retention, enclosure tolerance and service access.
11 mm Thickness for a Defined Enclosure Stack-Up
The 11 mm profile helps establish available depth around a high-capacity pouch cell. Include cushioning, protection components, thermal paths and nearby heat sources in the assembly review.
40mΩ for Load and Temperature Testing
The listed internal resistance supports an initial voltage-drop reference for the intended load. Test voltage stability across the target temperature range rather than treating the listed value as a guarantee.
High-temperature Category with Model-Specific Confirmation
115377 is included in ZERNE's high-temperature lithium polymer battery range. Contact ZERNE to confirm operating temperature, charging limits, capacity retention and long-term performance for the required configuration.
Battery calculation
Check Capacity, Energy and Estimated Runtime
Use the prefilled 115377 values or enter your own load assumptions for a quick energy and runtime estimate.
LiPo Battery Capacity Calculator
Energy is calculated from nominal voltage and capacity. Runtime uses the entered load power and an adjustable efficiency assumption.
Runtime and charge time are estimates, not guaranteed product performance.
23.31WhEstimated energy
41.96hEstimated runtime
1.00hIdeal charge time
How to Use the Result
The 115377 values are prefilled: 3.7 V, 6300mAh and an approximate 6300mA current derived from the listed 1C charge rate. Adjust the load power and efficiency to compare different operating scenarios.
- Use the displayed energy reference for an initial runtime comparison.
- Compare the estimate with measured device load and system efficiency.
- Review charger settings and protection limits for the finished configuration.
- Temperature, resistance growth and cutoff conditions affect actual performance.
Use the result as an initial estimate, then complete high-temperature sample testing, charger validation and final battery-specification review before production.
Integration guidance
Plan the 115377 LiPo Battery Around a Long Pocket and Heat Exposure
The 115377 battery should be evaluated as part of the finished device: reserve the 53 mm × 77 mm footprint, allow for the 11 mm depth, match the 1C charge rate and test voltage stability across the intended temperature range.
Reserve the 53 mm × 77 mm Battery Area
Allow space for the pouch cell, enclosure walls, cushioning, retention features, cable exit and service access around the long rectangular footprint.
Integrate the 11 mm Profile Into the Enclosure
Check enclosure depth, compression risk, nearby components and thermal paths around the high-capacity pouch cell before finalizing the mechanical stack-up.
Match the 1C Charge Rate Under the Intended Conditions
Set the charger and cell protection around the listed 1C rate, then confirm charging limits and temperature control for the finished product rather than assuming the category rating applies unchanged.
Applications & Solutions
Applications for the 115377 6300mAh High-Temperature LiPo Battery
The 115377 format is best evaluated against application-specific pocket geometry, energy demand and heat exposure rather than a generic device category. These three paths reflect its 11 mm × 53 mm × 77 mm envelope and 6300mAh capacity.
01Container Tracking Devices
The 53 mm × 77 mm footprint and 23.31Wh reference can be evaluated for long-interval container tracking equipment where service access, enclosure depth and radio duty cycle are defined.
Explore Container Tracking Devices →
02Smart Watches and Wearables
The 11 mm profile is a substantial depth reference for wearable equipment; compare it only when the housing, retention system and heat path can accommodate the long pouch format.
Explore Smart Watches and Wearables →
03Bar-Code Scanners
The long 77 mm battery area can be reviewed for industrial scanning terminals with a defined battery channel, grip clearance and controlled cable routing.
Explore Bar-Code Scanners →These application paths are starting points for OEM evaluation. Final suitability depends on actual load, runtime, temperature, protection, connector and assembly requirements.
READY FOR A FIT REVIEW?
Request a Technical Review →Confirm the 115377 Battery Fit
Share the finished-device pocket, load profile and temperature conditions to receive a focused recommendation for this 6300mAh format.
Related Technical Articles
Technical Guidance for Selecting a 6300mAh High-Temperature LiPo Battery
Use these resources to connect the 115377 geometry and energy target with temperature effects, current demand, energy planning and safe operation.
Temperature PlanningHow Temperature Affects the Performance of a LiPo Battery
Understand how temperature changes capacity, resistance, charging and usable LiPo battery performance in the finished device.
Read the Temperature Guide →
Current DemandWhat Is the C Rating of a LiPo Battery and Why It Matters
Review how current demand and C-rating concepts affect peak-load discussions, startup behavior and battery selection.
Read the C-Rating Guide →
Energy PlanningWhat Is Energy Density in a Lithium Polymer Battery?
Relate the 23.31Wh reference to the 11 mm × 53 mm × 77 mm envelope when comparing runtime planning, usable volume and the final battery pocket.
Read the Energy-Density Guide →LiPoSAFE
DESIGNCharging · protection · heat
Protection PlanningDESIGNCharging · protection · heat
Why Do LiPo Batteries Explode and How to Prevent It
Review charging, handling, storage and protection considerations before integrating a lithium polymer battery near heat sources.
Read the LiPo Safety Guide →OEM high-temperature battery support
Start the 115377 Inquiry with the Heat-Exposure Requirement
A complete inquiry can include the required runtime, device load, 53 mm × 77 mm battery pocket, 11 mm depth, target temperature, charger and documentation needed to evaluate this 6300mAh high-temperature cell.
Information to Include in Your Inquiry
Share the product conditions that determine how the 115377 model will perform in the finished device, especially its temperature profile, runtime target, peak load and charging window.
- Target runtime and duty cycle
- Voltage, capacity and battery pocket
- Peak current and heat-exposure profile
- Charger and charging temperature
- Operating and storage environment
- Connector, quantity and approval timing
When a Standard Format Is Not Enough
ZERNE can discuss alternate high-temperature chemistry, capacity, geometry, protection, connector and thermal requirements when the 115377 specification does not match the finished product.
Discuss a Custom BatteryFAQ
115377 High-Temperature Battery Questions
Find answers about the 115377 3.7 V 6300mAh lithium polymer battery, including its 11 mm profile, 53 mm × 77 mm footprint, 1C charge rate, 40mΩ internal resistance and high-temperature design considerations.
What Are the Dimensions of the 115377 LiPo Battery?
The 115377 battery measures 11 mm in thickness, 53 mm in width and 77 mm in length.
How Much Capacity and Energy Does the 115377 Battery Provide?
The rated capacity is 6300mAh at a nominal voltage of 3.7 V. Its calculated energy is approximately 23.31Wh before system losses.
What Charging Rate Is Listed for the 115377 Battery?
The 115377 battery has a listed 1C charging rate. Contact ZERNE to confirm the charging current, charging temperature and protection limits for your configuration.
What Is the Internal Resistance of the 115377 Battery?
The listed internal resistance is 40mΩ. Resistance can vary with temperature, state of charge, test method and production tolerance, so voltage stability can be assessed under the intended device load.
Is the 115377 Battery Suitable for High-Temperature Applications?
115377 is included in ZERNE's high-temperature lithium polymer battery range. Contact ZERNE to confirm operating temperature, charging limits, capacity retention and long-term performance for the required configuration.
What Should Be Checked Before Integrating the 115377 Battery?
Review the 53 mm × 77 mm battery area, 11 mm depth, heat sources, thermal paths, cushioning, cable exit, protection design, charger, peak load and connector requirements with ZERNE.
High-temperature battery inquiry
Review the 115377 Battery Fit with Zerne
Share the application, runtime target, load profile, 53 mm × 77 mm battery area, 11 mm depth, heat-exposure condition and annual demand so ZERNE can recommend the right sample and validation path.
- Product model and target application
- Required voltage, capacity and runtime
- Operating temperature and heat-exposure profile
- Charger, connector and documentation needs