1.85Wh Calculated Energy in a Thin Profile
This 3.7 V lithium polymer battery provides a larger energy budget than miniature 230mAh formats while keeping the listed thickness at 5.0 mm for compact device planning.
3.7 V High-Temperature Lithium Polymer Battery
3.7 V 500mAh Lithium Polymer Battery 503033
The 503033 lipo battery combines 3.7 V nominal voltage, 500mAh capacity, a 5.0 mm × 30 mm × 33 mm pouch envelope, a 1C charging rate and 80mΩ internal resistance. Its thin, compact format provides approximately 1.85Wh of calculated energy for electronic products that need more capacity than a miniature cell while maintaining a defined battery pocket.
50303330 × 33 mm5.0 mm profile
500mAh LiPo503033 reference format
503033 High-Temperature LiPo BatteryNeutral reference visual for thin-format connected equipment
3.7 V · 1.85 WhProduct snapshot
A Thin 500mAh LiPo Format for Compact Heat-Exposed Electronics
The 503033 LiPo battery combines 500mAh capacity with a 5.0 mm × 30 mm × 33 mm pouch envelope. Its thin profile gives product teams a practical starting point for increasing energy within a compact enclosure while reviewing heat exposure, insulation and service access. See the high-temperature lithium polymer battery range when comparing nearby formats.
80mΩ for Load and Heat Evaluation
The listed 80mΩ internal resistance gives engineering teams a reference for voltage-drop discussions at the intended load. Temperature, state of charge and test method still need to be considered in the finished device.
3.7 VNominal voltage
≈1.85WhCalculated energy
5.0 mmBattery thickness
33 mmBattery length
Technical data
503033 Battery Specifications
The 503033 lipo battery combines a 3.7 V nominal voltage, 500mAh capacity, 1C charge rate and 5.0 mm × 30 mm × 33 mm dimensions for compact electronics and high-temperature battery evaluation.
| 503033 Mechanical and Electrical Specifications | |
|---|---|
| Product number | 503033 |
| Nominal voltage | 3.7 V |
| Rated capacity | 500mAh |
| Charge rate | 1C |
| Battery dimensions | 5.0 mm × 30 mm × 33 mm |
| Internal resistance | 80mΩ |
| Calculated Electrical References | |
| Standard charge current | Approx. 250mA |
| Rapid charge current | Approx. 500mA |
| Standard discharge current | Approx. 100mA |
| Maximum discharge current | Approx. 500mA |
| Calculated energy | Approx. 1.85Wh |
The 503033 lithium polymer battery is listed at 3.7 V, 500mAh, 1C charging, 5.0 mm × 30 mm × 33 mm and 80mΩ internal resistance. Confirm charging, discharge, protection, connector and high-temperature performance for the intended device and operating conditions before production.
Product characteristics & advantages
Why Evaluate the 503033 500mAh High-Temperature LiPo Battery?
The 503033 model brings together a 1.85Wh calculated energy budget, 5.0 mm profile, 30 mm × 33 mm footprint, 500mAh capacity and 80mΩ internal resistance. Its main design value is a thin, moderate-capacity format for compact products that need more energy than a miniature cell.
The 503033 lithium polymer battery is intended for OEM teams that need to increase available energy without immediately moving to a much thicker battery format. Its approximately 1.85Wh calculated energy supports early comparisons of reporting intervals, standby demand and short active-load periods in compact products. The 5.0 mm thickness and 30 mm × 33 mm plan area provide a defined mechanical reference for slim enclosures and handheld electronics. The listed 1C charge rate and 80mΩ internal resistance provide starting points for charger matching and voltage-drop discussions. Because temperature affects resistance, voltage stability, available capacity and charging behavior, contact ZERNE to confirm the final high-temperature configuration.
500mAh for Longer Compact-Device Operation
The 500mAh capacity and approximately 1.85Wh calculated energy help compare standby demand, sensing intervals and active operating periods when a 230mAh-class format is not sufficient.
5.0 mm Thickness for Shallow Battery Pockets
The 5.0 mm profile helps define available enclosure depth. Include cushioning, protection components, thermal paths and nearby heat sources in the assembly review.
30 mm × 33 mm Plan Area for Compact Layouts
The 30 mm × 33 mm footprint gives designers a small rectangular battery reference. Review cable exit, retention, enclosure tolerance and service access around the pouch cell.
80mΩ for Load and Temperature Testing
The listed internal resistance supports an initial voltage-drop reference for the intended load. Test voltage stability across the target temperature range rather than treating the listed value as a guarantee.
High-temperature Category with Model-Specific Confirmation
503033 is included in ZERNE's high-temperature lithium polymer battery range. Contact ZERNE to confirm operating temperature, charging limits, capacity retention and long-term performance for the required configuration.
Battery calculation
Check Capacity, Energy and Estimated Runtime
Use the prefilled 503033 values or enter your own load assumptions for a quick energy and runtime estimate.
LiPo Battery Capacity Calculator
Energy is calculated from nominal voltage and capacity. Runtime uses the entered load power and an adjustable efficiency assumption.
Runtime and charge time are estimates, not guaranteed product performance.
1.85WhEstimated energy
3.33hEstimated runtime
1.00hIdeal charge time
How to Use the Result
The 503033 values are prefilled: 3.7 V, 500mAh and an approximate 500mA current derived from the listed 1C charge rate. Adjust the load power and efficiency to compare different operating scenarios.
- Use the displayed energy reference for an initial runtime comparison.
- Compare the estimate with measured device load and system efficiency.
- Review charger settings and protection limits for the finished configuration.
- Temperature, resistance growth and cutoff conditions affect actual performance.
Use the result as an initial estimate, then complete high-temperature sample testing, charger validation and final battery-specification review before production.
Integration guidance
Plan the 503033 LiPo Battery Around Thin Assembly and Heat Exposure
The 503033 battery should be evaluated as part of the finished device: reserve the 30 mm × 33 mm footprint, allow for the 5.0 mm depth, match the 1C charge rate and test voltage stability across the intended temperature range.
Reserve the 30 mm × 33 mm Battery Area
Allow space for the pouch cell, enclosure walls, cushioning, retention features, cable exit and service access around the compact battery footprint.
Protect the 5.0 mm Thin Profile
Check enclosure depth, compression risk, nearby components and thermal paths around the thin pouch cell before finalizing the mechanical stack-up.
Match the 1C Charge Rate Under the Intended Conditions
Set the charger and cell protection around the listed 1C rate, then confirm charging limits and temperature control for the finished product rather than assuming the category rating applies unchanged.
Applications & Solutions
Applications for the 503033 500mAh High-Temperature LiPo Battery
The 503033 format is best evaluated against application-specific pocket geometry, energy demand and heat exposure rather than a generic device category. These three paths reflect its 5.0 mm × 30 mm × 33 mm envelope and 500mAh capacity.
01Bar-Code Scanners
The 5.0 mm thickness and 30 mm × 33 mm footprint provide a thin reference for scanner handles and compact terminals with limited board-side depth.
Explore Bar-Code Scanners →
02Smart Door Locks
The 500mAh capacity can be compared with connected lock electronics where the pouch must stay shallow while the enclosure reserves room for the latch, controller and cable exit.
Explore Smart Door Locks →
03Smart Watches and Wearables
The thin 5.0 mm pouch gives wearable product teams a defined starting point for energy and enclosure review, subject to the final housing, duty cycle and thermal path.
Explore Smart Watches and Wearables →These application paths are starting points for OEM evaluation. Final suitability depends on actual load, runtime, temperature, protection, connector and assembly requirements.
READY FOR A FIT REVIEW?
Request a Technical Review →Confirm the 503033 Battery Fit
Share the finished-device pocket, load profile and temperature conditions to receive a focused recommendation for this 500mAh format.
Related Technical Articles
Technical Guidance for Selecting a 500mAh High-Temperature LiPo Battery
Use these resources to connect the 503033 geometry and energy target with temperature effects, current demand, energy planning and safe operation.
Temperature PlanningHow Temperature Affects the Performance of a LiPo Battery
Understand how temperature changes capacity, resistance, charging and usable LiPo battery performance in the finished device.
Read the Temperature Guide →
Current DemandWhat Is the C Rating of a LiPo Battery and Why It Matters
Review how current demand and C-rating concepts affect peak-load discussions, startup behavior and battery selection.
Read the C-Rating Guide →
Energy PlanningWhat Is Energy Density in a Lithium Polymer Battery?
Relate the 1.85Wh reference to the 5.0 mm × 30 mm × 33 mm envelope when comparing runtime planning, usable volume and the final battery pocket.
Read the Energy-Density Guide →LiPoSAFE
DESIGNCharging · protection · heat
Protection PlanningDESIGNCharging · protection · heat
Why Do LiPo Batteries Explode and How to Prevent It
Review charging, handling, storage and protection considerations before integrating a lithium polymer battery near heat sources.
Read the LiPo Safety Guide →OEM high-temperature battery support
Start the 503033 Inquiry with the Heat-Exposure Requirement
A complete inquiry can include the required runtime, device load, 30 mm × 33 mm battery pocket, 5.0 mm depth, target temperature, charger and documentation needed to evaluate this 500mAh high-temperature cell.
Information to Include in Your Inquiry
Share the product conditions that determine how the 503033 model will perform in the finished device, especially its temperature profile, runtime target, peak load and charging window.
- Target runtime and duty cycle
- Voltage, capacity and battery pocket
- Peak current and heat-exposure profile
- Charger and charging temperature
- Operating and storage environment
- Connector, quantity and approval timing
When a Standard Format Is Not Enough
ZERNE can discuss alternate high-temperature chemistry, capacity, geometry, protection, connector and thermal requirements when the 503033 specification does not match the finished product.
Discuss a Custom BatteryFAQ
503033 High-Temperature Battery Questions
Find answers about the 503033 3.7 V 500mAh lithium polymer battery, including its 5.0 mm profile, 30 mm × 33 mm footprint, 1C charge rate, 80mΩ internal resistance and high-temperature design considerations.
What Are the Dimensions of the 503033 LiPo Battery?
The 503033 battery measures 5.0 mm in thickness, 30 mm in width and 33 mm in length.
How Much Capacity and Energy Does the 503033 Battery Provide?
The rated capacity is 500mAh at a nominal voltage of 3.7 V. Its calculated energy is approximately 1.85Wh before system losses.
What Charging Rate Is Listed for the 503033 Battery?
The 503033 battery has a listed 1C charging rate. Contact ZERNE to confirm the charging current, charging temperature and protection limits for your configuration.
What Is the Internal Resistance of the 503033 Battery?
The listed internal resistance is 80mΩ. Resistance can vary with temperature, state of charge, test method and production tolerance, so voltage stability can be assessed under the intended device load.
Is the 503033 Battery Suitable for High-Temperature Applications?
503033 is included in ZERNE's high-temperature lithium polymer battery range. Contact ZERNE to confirm operating temperature, charging limits, capacity retention and long-term performance for the required configuration.
What Should Be Checked Before Integrating the 503033 Battery?
Review the 30 mm × 33 mm battery pocket, 5.0 mm depth, heat sources, thermal paths, cushioning, cable exit, protection design, charger, peak load and connector requirements with ZERNE.
High-temperature battery inquiry
Review the 503033 Battery Fit with Zerne
Share the application, runtime target, load profile, 30 mm × 33 mm battery pocket, 5.0 mm depth, heat-exposure condition and annual demand so ZERNE can recommend the right sample and validation path.
- Product model and target application
- Required voltage, capacity and runtime
- Operating temperature and heat-exposure profile
- Charger, connector and documentation needs